Correct: B)
Explanation: Maximum permissible airspeeds (VNE, VNO, etc.) are published in the Pilot's Operating Handbook (POH/AFM), displayed on the cockpit instrument panel (placard), and indicated on the airspeed indicator by the red line (VNE) and arc markings. The AIP ENR (A) does not contain aircraft-specific speed limitations. Approach charts and VSI (B) do not show speed limits. The briefing room posting (C) is informal and not authoritative.
Correct: A)
Explanation: The airspeed indicator is a required instrument for safe flight; without it a pilot cannot determine safe operating speeds, stall speed, or structural speed limits. An inoperative airspeed indicator means the aircraft must remain on the ground until the instrument is serviceable. No exception exists for local aerodrome patterns (B) or GPS substitute (D — GPS ground speed is not equivalent to IAS for aerodynamic purposes). Absence of maintenance (A) is irrelevant to the operational requirement.
Correct: A)
Explanation: During a left turn, a yaw string deflecting to the left indicates the aircraft is slipping into the turn (too much bank relative to rudder input). To centre the string in a slip, the pilot needs to increase bank to steepen the turn and reduce rudder (less rudder in the turn direction). This is opposite to correcting a skid. Options B, C, and D use incorrect combinations for correcting a slip in a left turn.
Correct: C)
Explanation: Winglets are upward (or downward) curving extensions at the wingtip that reduce induced drag by weakening the wingtip vortex — the main source of induced drag on a finite wing. They do not primarily increase aspect ratio efficiency (A — though functionally similar, they are a different mechanism), are not specifically for high-speed performance (C), and do not increase lift or turning agility (D).
Correct: C)
Explanation: Dynamic pressure (q) is defined by Bernoulli's equation as q = ½ρv², where ρ is air density and v is airflow speed. Dynamic pressure depends directly on air density and the square of velocity. Lift and drag coefficients (A) are aerodynamic effects that depend on dynamic pressure, not the other way around. Air pressure and temperature (D) influence density indirectly but are not the direct parameters in the formula.
Correct: C)
Explanation: The airspeed indicator, altimeter, and vertical speed indicator are all connected to the static pressure port. If the static pressure system is blocked (e.g., by ice, water, or a cover left on), all three instruments will give erroneous readings simultaneously. A blocked pitot tube (C) would affect only the airspeed indicator. A leaking compensating vessel (B) affects only the VSI. An electrical failure (D) does not affect these purely pneumatic instruments.
Correct: B)
Explanation: The altimeter's reference pressure (subscale) must be set before every flight to the correct local QNH/QFE so that the altimeter reads the correct altitude or height. During cross-country flights, QNH changes as the pilot moves between pressure regions, so updates are required when crossing into new altimeter setting regions. Monthly (C) or only after maintenance (A) settings would result in significant altitude errors.
Correct: D)
Explanation: Magnetic inclination (dip) is the angle between the Earth's magnetic field vector and the horizontal plane at any given location. It is 0° at the magnetic equator and 90° at the magnetic poles. Deviation (A) is the error caused by magnetic fields within the aircraft. Magnetic variation/declination (B) is the angle between magnetic and true north. Option D describes aircraft heading, which is unrelated.
Correct: D)
Explanation: The airspeed indicator measures IAS (Indicated Airspeed), which is derived from dynamic pressure. At lower air density (hot day, high altitude), TAS is higher than IAS for the same dynamic pressure. The aerodynamic behaviour of the wing (lift, stall) depends on dynamic pressure (and thus IAS), not on TAS. Therefore stall occurs at the same IAS regardless of density. The approach should be flown at the same IAS as always (B). Adding speed (D) or reducing IAS (C) based on temperature alone is not correct for stall margin management with IAS.
Correct: D)
Explanation: The load factor (n) is the ratio of the aerodynamic lift acting on the aircraft to the aircraft's weight: n = L/W. In level unaccelerated flight, n = 1. In turns or pull-ups, n increases. It does not describe weight/thrust (A), drag/lift (B), or thrust/drag (D) relationships.
Correct: D)
Explanation: Static pressure is the pressure of the undisturbed ambient airmass — the atmospheric pressure acting equally in all directions at a given altitude. It is sensed through flush static ports on the fuselage skin. It is not the cabin pressure (A), not related to orderly flow direction (C — that is dynamic pressure), and is not sensed by the pitot tube alone (D — the pitot senses total pressure).
Correct: C)
Explanation: Magnetic inclination (dip) is the angle between the Earth's total magnetic field vector and the local horizontal plane. At the magnetic equator, field lines are horizontal (0° dip); at the poles, they are vertical (90° dip). Deviation (A) is caused by onboard magnetic interference. Variation/declination (B) is the angle between magnetic and geographic north. Option D describes aircraft heading relative to true north.
